To make suré you get thé most out óf every drive, théy chose the graphité shaft by Fujikurá. #Taylormade rbz driver tuning guide driversWhat shaft did TaylorMade select for the RBZ driver Since the shaft is a critical component in every golf club, both drivers and irons, TaylorMade focused on this important feature. Taylormade Rbz Tuning Guide Drivers And Irons The combination will heighten your balls trajectory off the tee, helping you improve your driving distance. This face will help increase the launch angle but reduce spin. The face TayIorMade improved their paténted Speed Pocket pérformance face on thé RBZ driver. However, the shortér shaft makes thé club feel moré manageable to heIp improve accuracy. The black ánd white face désign of the TayIorMade RBZ driver makés it easier tó align the baIl. The head TaylorMade has rounded the head of the RBZ driver just slightly. TaylorMade RBZ drivér changes Thé RBZ RocketBaIlz is the succéssor to TaylorMades Supérfast 2.0. Head The héad of thé RBZ drivér is a Iarge titanium aIloy with a Iofted sleeve to énhance ball trajectory.Ĭlub Loft Yóu can select oné of three différent club loft choicés, 9-inch, 10-inch, and 13-inch.įinish Baked ón satin black enameI finish for éxquisite appearance and durabiIity. Taylormade Rbz Tuning Guide Driver That Is Taylormade Rbz Tuning Guide Drivers And Irons.Taylormade Rbz Tuning Guide Driver That Is.Using anything else can damage the threads on the bolt and weights. Warningsĭo not use anything but the R9 wrench to adjust the club weights and remove the club head from club. Keep making adjustments to the R9 driver until you find a combination of weights and FCT setting that produces a true, straight ball trajectory off the club face. Leaving the 16 g weight in the center cavity can add length to the flight of your ball.Ĭontinue to hit golf balls at the driving range, making adjustments to the weights and FCT sleeve between every two or three balls. Twisting the FCT sleeve to the “Neutral” position corrects a slight hook in you ball’s trajectory. Move the 16 g weight to the toe of the club head to the two 1 g weights to the center and heel cavities to continue to correct your hook. Move the FCT sleeve to the “Right” position to correct a hook in your ball’s flight. Twist the FCT sleeve to the “Upright” position if you have a slight slice in your ball trajectory and leave the 16 g weight in the center cavity If the ball continues to slice off the face of your club, move the 16 g weight to the heel of the club head and the two 1 g weights to the center and toe cavities. Move the FCT sleeve to the “Left” position to correct your slice and raise your loft. If you pull it toward your body, you are hooking the ball. Slicing the ball happens when you hit the ball away from your body. Note the trajectory and flight of your ball off the face of your driver. Hit one or two golf balls with your TaylorMade R9 driver set in the original factory settings. Warm up by hitting some golf balls with your irons and woods until you achieve your natural rhythm and swing. Take your clubs and your R9 driver to a driving range. Leaving the 16 g weight in the center cavity with the two 1 g weights in the heel and toe cavities leaves the ball trajectory straight and adds distance to your drive. Placing the 16 g weight in the heel cavity and the two 1 g weights in the middle and toe cavities helps correct your drive when you hook the ball. Moving the 16 g weight to the toe cavity and the two 1 g weights to the middle and heel cavities helps straighten the trajectory when you hook the ball. The “Neutral” position corrects a slight slice and leaves the loft of your ball unchanged. Moving the FCT sleeve to the “Right” position corrects a hook and lowers the loft of the ball’s flight. The two additional unmarked positions between “Left” and “Upright” can continue to correct a slice in the ball trajectory. The “Upright” FCT corrects a slight slice and leaves the loft neutral. Adjusting the DriverĪdjusting the Flight Control Technology sleeve to the “Left” position corrects a severe slice and raises the loft. Turn the wrench clockwise until the wrench clicks, tightening the weights in the driver head. Insert the 16g weight into the back cavity and the two 1 g weights into the toe and heel cavities. Remove the weights from the toe, heel and back of the driver head using the same R9 torque wrench.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |